用于各种pom、聚甲 醛 、赛钢料、pom赛钢料、电木、电泳、pa尼龙塑料、改良性塑料、电泳、pom赛钢料、uv表面及pcb线路板表面丝印及移印，不需加固化剂 ，不需烘烤，即可获得优异的附着力。 油墨特性： 1、平光、附着力佳、耐汽油、耐化学品； 2、手感好，流平性佳、面光洁； 3、表面硬度好，耐冲击性能强、抗刮伤； 4、耐汽油、耐酒精、耐化学品程度佳； 印刷： 选用网目为100-350目，以120t网纱计算涂覆盖面积每公斤达30~35㎡。 表干时间自然挥发5-15分钟，实干时间在24小时以内，48小时后达优秀性能。 1．用配套专用稀释剂 开油水 2．用718洗网水洗网。 3．或添加配套硬化剂 10％可增加附着力,提高墨膜硬度。 4．烤箱80℃烘烤10分钟佳能更优。 测试方法（完全干燥后）： 1．3m胶纸粘在画有百格的油墨表面45度角迅速拉起不脱油。 使用方法： 1．建议用我公司专用稀释剂 进行稀释，不建议使用783慢干稀释剂 稀释，使用前应充分搅拌，用后随时密封。 2．搅拌时加本公司配套开油水10-12％，稀释到印刷适合粘度，移印稀释使用移印专用稀释剂 ；用718洗网水清洗。 3．不得与其它类型油墨混合使用，否则容易出现其他附着力，化学反应等不良现象。 4. 加入固化剂 的油墨使用时限为8小时，过期请弃用，剩余油墨不可回收 注意事项： 1．各种承印物料的外观相似，但可能会是不同的材料，客户需先试印，确其符合要求后，再批量生产。 2．在移印过程中，如出现拉丝或散开，可适当加入一些慢干膏即可; 3．环境温度过高，将会影响油墨原有质量。白色超越150都会变色，烘烤时请用木质材料垫底进行烘烤，不得直接接触铁 4．根据气候变化，请远离火源，阴暗处15度-30度环境下存放pom steel material silk screen printing ink
for a variety of pom, poly formaldehyde, steel material, pom steel material, bakelite, electrophoresis, pa nylon plastic, modified plastics, electrophoresis, pom steel material, uv surface【敏感词】pcb circuit board surface screen printing【敏感词】printing, do not need to add curing agent,【敏感词】does not need to bake, can obtain excellent adhesion. ink characteristics: 1, gloss, adhesion, good gasoline resistance, chemical resistance; 2, good hand feeling, good leveling, smooth surface; 3, good surface hardness, strong shock resistance, anti scratch; 4, gasoline resistance, alcohol resistance, chemical resistance【敏感词】good; printing: choose mesh is 100-350 mesh, with 120t gauze calculation coated area coverage per kilogram of 30 to 35 square meters. table dry time natural volatile 5-15 minutes, hard work time within 24 hours, 48 hours after the best performance. 1 with matching special thinner open oil water 718 with 2 washing net. 3【敏感词】adding matching hardening agent 10％ can increase adhesion, improve the ink film hardness. 4 oven 80 degrees bake 10 minutes canon better. test method (dry): 1.3m gummed paper hundred grid ink surface angle of 45 degrees quickly pulled off the oil painting. usage: 1 recommended to use my company's special diluent dilution, do not recommend the use of 783 slow dry dilution dilution, before use should be fully stirred, sealed at any time after use. 2. mixing cabernet companies supporting open water10-12％【敏感词】dilution to printing for viscosity, printing the dilution used printing special thinner; with 718washing network water cleaning. 3 shall not be mixed with other types of ink,【敏感词】else it is prone to other adhesion, chemical reactions【敏感词】other undesirable phenomena. 4. add the curing agent of ink usage time is 8 hours【敏感词】expired please abandoned【敏感词】the remaining ink not recycling matters needing attention: 1. all kinds of printing material similar in appearance, but may be different materials, customers need to try printing【敏感词】ensure its requirements,【敏感词】then a batch production. 2. in the printing process, such as drawing【敏感词】spread can be appropriate to add some slow dry paste can; 3 the ambient temperature is too high, will affect the ink the original quality. white beyond 150 color, please use woodiness material bottom baking baking shall not be in direct contact with the iron. according to the climate change, please stay away from fire, shadows 15 degrees-30 degrees environment storage
免费会员